How to Make a Bean Bag Toy

Bean bag toys have been around for q pandora bracelet uite some time. They are one of the safest toys around for your children and pets to play with. The best thing about bean bag toys which are made at home is if they become worn or torn, you can reuse the dried bean filling to make another bean bag toy. Kids find tossing bean bags around is rather fun and a way to enjoy an afternoon. You can create the bean bags in shape and size imaginable. While many who think of making a bean bag at home, they think of the sizes they had when they were kids themselves.

There are other ways and reasons to make bean bags. You can make bean bag style animals, chairs, pillows, a neck rest for riding and sitting for hours, and wrist rest for your computer.

In some instances, people have made bean bags to help relieve arthritis pain and menstrual cramps. They will heat the bean bag in the oven or microwave for a few minutes, just long enough to get the beans warm, to place on their joints that are in pain or to lay across their abdominal area pandora bracelet for menstrual cramps for relief.

Materials for Making a Bean Bag

Fabric scraps. You can use fabric scraps that are large enough to make the bean bags. The size of the fabric will depend on how big a bean bag you want to make.

Dried Beans. Any type and style of dried beans or peas will work for your bean bags. You can also use dried split peas if you prefer, since they are smaller in size. However, you will want to keep the dried beans out of the reach of infants and toddlers so they will not become choked on them before they are placed in the sealed fabric casing.

pandora bracelet Sewing machine, thread and needle. You will need either the sewing machine or a needle and thread or both to make the bean bags. This is a simple sewing project.

Scissors. The scissors will be needed to cut out the sizes and shapes for the bean bags from the fabric you have chosen.

Directions for Making the Bean Bag

NOTE: The directions are for making a square bean bag. The size of the square is up to you.

Cut out two squares from the fabric you have chosen. Place the right sides together. Sew three sides of the square together with a quarter inch seam allowance.

Fill the square with the dried beans leaving at least half an inch from the top. By leaving the half inch allowance with the dried beans, this will allow the beans to spread out once the open side is sewn shut. You can leave at least a quarter inch of room inside the square as well.

Sew the open side shut.

When it comes to making bean bags, you can get your kids to help make them. This allows bonding time between the parent and grandparent bonding time with the kids. Also, by allowing the kids to help in the process of making the bean bags, they can learn math skills. For instance, they will learn how to measure in cups, inches, and to count.

Not only will the kids learn those skills, they will improve their motor skills with the use of the measuring cups, scissors, rulers, and various other objects being used for the craft project. They can also learn a little science in the process. They can learn about man made and nature made items.

Getting the kids involved in craft projects is a great way to keep the learning process going while they are having fun. After all, no one ever said education had to be boring and mundane.

How to Turn Your Basement into a Kid Friendly Play Room Without Spending Lot Money?There are lots of people who hav pandora bracelet e basements that they just don’t know what to do with. H O R S E Bean Bag GameThis is a simple new version of the H O R S E basket ball game you can make with the kids, but using bean bags.

How to Make a Bean Bag Toss Board

Bean bag toss, also called cornhole, has really taken off over the past few years. It is a common site at campgrounds, tailgating events, parties, and driving through neighborhoods on a summer evening. My wife and I were hooked on bean bag toss after playing a few times with our neighbors. We decided to build our own set of boards.

Easy to Follow Steps to Build Your own Board SetThe official length of the boards is two feet wide by four feet long, however, if plan to take your boards with you, two feet wide by three feet is considered tailgate size. The instructions below are for boards that are two by three feet. If you prefer to make boards that are four feet long, just modify the cutting instructions by the difference.

Shopping List for Building Bean Bag BoardsThe shopping list is for building two boards so that you will have a set. Since this is an outdoor bean bag board, I suggest using pressure treated 2x4s. Remember that when dealing with 2x4s, remember that they are actually 1.5″ x 3.5″. Here are the items that you will need to purchase:

(1) pandora bracelet 4′ x 8′ x ” sheet of plywood (not MBF or chipboard)

(4) 2″ x 4″ x 8′

(4) 4″ x ” bolts

(8) ” washers

(1) Box of 3 ” screws

(1) Box of 1 ” screws

Wood putty

Paint (Colors of your choosing)

Bean Bag Board Cut ListCut the Face Boards

Using a pandora bracelet table saw or circular saw, take the 4×8 sheet of plywood and cut out two sections that are 24″ x 36″ each.

On each board of the cut outs, select the best side of the board and mark the underneath side as bottom.

On the front side, measure down 9 inches from the top and make a mark. Then measure 12 inches from one of the sides and make another mark. At the point the marks cross, take the compass and draw a circle with a 3 inch radius.

Drill several holes using a inch drill bit around the ins pandora bracelet ide of the circle.

Insert the jigsaw blade in one of the holes and carefully cut out the circle on each board. Sand the inside of the circle and try to make it is round as possible. It does not have to be perfect.

Using the miter saw, take the first 2×4 and cut it into the following lengths: 36″, 36″, and 20 . Place those pieces with one of the face boards.

Take a second 2×4 and cut it into the following lengths: 36″, 36″, and 20 . Place those pieces with the other face board.

Take another 2×4 and cut it into the following lengths: 20 , 11 , 11 , 17 , 20 , and 11 . Place the 20 , 11 , 11 , and the 17 cuts with the first face board. Place the remaining two cuts with the other face board.

Take the last 2×4 and cut it into the following lengths: 11 and 17 . Place these two cuts with the second face board.

Take the four 11 pieces, which will make up the legs, and round one side of each of them using the jig saw.

Woodworking LinksTools Every Homeowner Should Have

Every homeowner will need tools at some point. Select the best ideas that work for your needs.

Assembly Instructions of Your Bean Bag BoardNow that we have made all of our cuts, we can start assembling the boards. Here are the easy to follow instructions (Repeat for the second bean bag board):

Grab two 36″ boards and two 20 ” boards and lay down the 36″ boards parallel to each other. Insert one 20 ” between the tw pandora bracelet o 36″ boards at the top and the other one at the bottom, forming a rectangle. Square it up and screw the frame together by using the 3 ” screws. Drive in at least two screws into each end.

From the top of the frame, measure down 3 ” on each of the 36″ sides of the frame and make a mark in the middle of the 2×4. Drill a ” hole in each side of the frame where the mark is. Grab two of the 11 ” leg boards and measure down 3 ” and make a mark in the center of each one. Drill a ” hole in each of the legs. Grab a 4″ bolt and slide it through the outside of the frame on each side. Place one ” washer on the bolt on each side. Side the legs down the bolt and place another ” washer on the bolt. Grab a nut and screw it on the bolt until tight. Do the same thing on the other side. Take the 17 ” board and insert it near the bottom of the legs, about an inch up from the bottom. Using the 3 ” screws, secure the brace between the legs. The legs should be able to easily open and close to make your board easily portable.

How to Make a Bean Bag Toss Board

Bean bag toss, also called cornhole, has really taken off over the past few years. It is a common site at campgrounds, tailgating events, parties, and driving through neighborhoods on a summer evening. My wife and I were hooked on bean bag toss after playing a few times with our neighbors. We decided to build our own set of boards.

Easy to Follow Steps to Build Your own Board SetThe official length of the boards is two feet wide by four feet long, however, if plan to take your boards with you, two feet wide by three feet is considered tailgate size. The instructions below are for boards that are two by three feet. If you prefer to make boards that are four feet long, just modify the cutting instructions by the difference.

Shopping List for Building Bean Bag BoardsThe shopping list is fo pandora bracelet r building two boards so that you will have a set. Since this is an outdoor bean bag board, I suggest us pandora bracelet ing pressure treated 2x4s. Remember that when dealing with 2x4s, remember that they are actually 1.5″ x 3.5″. Here are the items that you will need to purchase:

(1) 4′ x 8′ x ” sheet of plywood (not MBF or chipboard)

(4) 2″ x 4″ x 8′

(4) 4″ x ” bolts

(8) ” washers

(1) Box of 3 ” screws

(1) Box of 1 ” screws

Wood putty

Paint (Colors of your choosing)

Bean Bag Board Cut ListCut the Face Boards

Using a table saw or circular saw, take the 4×8 sheet of plywood and cut out two sections that are 24″ x 36″ each.

On each board of the cut outs, select the best side of the board and mark the underneath side as bottom.

On the front side, measure down 9 inches from the top and make a mark. Then measure 12 inches from one of the sides and make another mark. At the point the marks cross, take the compass and draw a circle with a 3 inch radius.

Drill several holes using a inch drill bit around the inside of the circle.

Insert the jigsaw blade in one of the holes and carefully cut out the circle on each board. Sand the inside of the circle and try to make it is round as possible. It does not have to be perfect.

Using the miter saw, take the first 2×4 and cut it into the following lengths: 36″, 36″, and 20 . Place those pieces with one of the face boards.

Take a second 2×4 and cut it into the following lengths: 36″, 36″, and 20 . Place those pieces with the other face board.

Take another 2×4 and cut it into the following lengths: 20 , 11 , 11 , 17 , 20 , and 11 . Place the 20 , 11 , 11 , and the 17 cuts with the first face board. Pl pandora bracelet ace the remaining two cuts with the other face board.

Take the last 2×4 and cut it into the following lengths: 11 and 17 . Place these two cuts with the second face board.

Take the four 11 pieces, which will make up the legs, and round one side of each of them using the jig saw.

Woodworking LinksTools Every Homeowner Should Have

Every homeowner will need tools at some point. Select the best ideas that work for your needs.

Assembly Instructions of Your Bean Bag BoardNow that we have made all of our cuts, we can start assembling the boards. Here are the easy to follow instructions (Repeat for the second bean bag board):

Grab two 36″ boards and two 20 ” boards and lay down the 36″ boards parallel to each other. Insert one 20 ” between the two 36″ boards at the top and the other one at the bottom, forming a rectangle. Square it up and screw the frame together by using the 3 ” screws. Drive in at least two screws into each end.

From the top of the frame, measure down 3 ” on each of the 36″ sides of the frame and make a mark in the middle of the 2×4. Drill a ” hole in each side of the frame where the mark is. Grab two of the 11 ” le pandora bracelet g boards and measure down 3 ” and make a mark in the center of each one. Drill a ” hole in each of the legs. Grab a 4″ bolt and slide it through the outside of the frame on each side. Place one ” washer on the bolt on each side. Side the legs down the bolt and place another ” washer on the bolt. Grab a nut and screw it on the bolt until tight. Do the same thing on the other side. Take the 17 ” board and insert it near the bottom of the legs, about an inch up from the bottom. Using the 3 ” screws, secure the brace between the legs. The legs should be able to easily open and close to make your board easily portable.